FAQs
Diamonds and Jewellery
How do I know if a diamond is genuine?
You will not. You need to be an expert and use specialised equipment to make sure a diamond is real. Do not trust ideas like scratching a beer bottle (it may damage the diamond too), thermal conductivity, looking through, comparing weight, etc. If the diamond is accompanied by a certificate, you will know it is real and if it is treated artificially or not.
Which shape gives me the greatest value for my money?
Round brilliant diamond has the most brilliance, and the most popular. Fancy diamonds look more elegant in larger sizes. Also, they tend to look larger than they are by virtue of their shape. The choice of shape is also governed by the shape of the hand and Diamond Colour and Diamond Clarity. Round brilliant diamond hides defects and yellow tints the best.
What is the structure of a diamond?
1. Facet: any of the flat "sides" of the diamond.
2. Table: On a brilliant cut stone...the top octagonal facet
3. Girdle: The typically frosty white ring at the widest part.
4. Culet: The bottom point (actually a facet) on a brilliant cut stone
5. Pavilion: The portion of the stone below the girdle
6. Crown: The portion of the stone above the girdle
7. Diameter: Width of the diamond as measured thru the girdle
8. Fire: The quality of the diamond that breaks reflected light into a colourful array.
9. Depth – Height of Gemstone from Culet to Table
10. Brilliance: The quality of the diamond that reflects light without changing it (also called sparkle).
11. Fluorescence: The characteristic of some diamonds to fluoresce certain colours under some light.
12. Natural: Usually found on the girdle. A small section was on the side of the raw diamond. It appears as a slightly rough flat spot on the girdle.
13. Feather: A “crack” in a diamond, appears as a white feather within the stone.
Q. OK; now that I know the terminology, what are the more important factors?
The first six terms describe the geometry of the diamond. Fire and sparkle are variable characteristics that are determined by the proportions of the diamond. Modifying proportions to increase one may decrease the other! Look for a good balance of fire and sparkle. Fluorescence occurs naturally and synthetically. It is not common, so jewellers will try to command a higher price. In general, it does not change the value of the stone, but severe fluorescence gives stones an oily appearance in sunlight, and decreases its value. Naturals if not severe are not bad. Small feathers are common. Any crack that extends more than 1/3 of the way through the stone may cause structural problems.
How many facets does a diamond have?
On a brilliant full-cut stone, there are 58 facets; 32 facets plus the table above the girdle and 24 facets plus the culet below the girdle. Some stones with only 18 facets are refered to as "single cuts”.
What are the "four C's" relating to diamond quality?
The four C's are Carat (weight), Colour, Clarity and Cut of the stone.
1. Carat: The weight of the stone, referred to in points in case of small stones.
1 carat is 1/5 of a gram or 200 milligrams.
There are 100 points to a carat.
A 75 point stone is .75 carat.
"Carats" represent the weight and not the physical size of the stone.Example, 1 carat diamond is physically larger than a 1 carat ruby since ruby is denser than diamond.
2. Colour: Colour is usually undesirable in diamonds. Typically ratings will be alphabetical with the earlier letters of the alphabet having less colour.
AGS has a similar 0-10 scale.
D, E and F - "Colourless"
G, H, I & J - "near colourless"
K, L and M - faint yellow or "top silver"
N to Z - very light or “light yellow”
Z+ - grades are considered "fancy yellow"
Most stones you will find will be in the E-F to the J-K range.
3. Clarity: You will typically find ratings such as this:
GIA AGS CLARITY
FL 0 Flawless
IF 1 Internally Flawless
VVS1 1 Very, Very slightly included
VVS2 2 VVS1 to a less perfect degree
VS1 3 Very slightly included
VS2 4 VS1 to a less perfect degree
SI1 5 Slightly included
SI2 6 SI1 to a less perfect degree
I1 7-8 Included
I2 8-9 I1 to a less perfect degree
I3 9-10 Severely Included
Inclusions are imperfections within the stone. Inclusions range from bits of
carbon (black spots) to slight cracks (called "feathers") within the stone.
VVS1 to SI2 represent inclusions that are not visible to the naked eye.
4. Cut: All diamonds are cut. The resultant dimensions of the cut stones vary. All dimensions are given as a percentage of the width at the girdle. There are a few accepted ideal cuts, which have all of the proportions within a few percentage points of an optimum mathematical model. This optimum model returns maximum light through the top of the stone, resulting in maximum brilliance.
What is the most important C in the choice of a diamond? Colour or Clarity?
The most desirable colour of the diamond is white. The Colour scale ranges from D to Z, where D is the whitest of the white and hence most expensive. However, colours between E to H are regarded as very white, and you cannot make out the difference in colour once a diamond is set. However, diamond colour becomes more obvious as in larger size diamonds, or in shapes other than the round brilliant. For instance, the Asscher and the emerald cuts are more see-through with large facets, and require a higher colour and clarity than other shapes. Colour is something that can be discerned with the naked eye with practice (such as looking at the engagement ring everyday. Hence, it is advisable to buy as white a diamond as you can afford in your carat range, in an eye clean or better clarity. If a diamond has slight blue fluorescence, it could render your H or J colour whiter. Also, if the stone is very well cut, it makes both the clarity and colour look better. Clarity is not a factor you can judge only by looking at the diamond under magnification. Step cut diamond shapes like emerald and Asscher cuts require a higher quality of colour and clarity as they have large see-through facets which make it easy to see any imperfections.
What is the most important C in the choice of a diamond? Colour or Clarity?
The most desirable colour of the diamond is white. The Colour scale ranges from D to Z, where D is the whitest of the white and hence most expensive. However, colours between E to H are regarded as very white, and you cannot make out the difference in colour once a diamond is set. However, diamond colour becomes more obvious as in larger size diamonds, or in shapes other than the round brilliant. For instance, the Asscher and the emerald cuts are more see-through with large facets, and require a higher colour and clarity than other shapes. Colour is something that can be discerned with the naked eye with practice (such as looking at the engagement ring everyday. Hence, it is advisable to buy as white a diamond as you can afford in your carat range, in an eye clean or better clarity. If a diamond has slight blue fluorescence, it could render your H or J colour whiter. Also, if the stone is very well cut, it makes both the clarity and colour look better. Clarity is not a factor you can judge only by looking at the diamond under magnification. Step cut diamond shapes like emerald and Asscher cuts require a higher quality of colour and clarity as they have large see-through facets which make it easy to see any imperfections
What is most important of the 4 Cs in India?
In India, Colour takes precedence over Cut. The order or priority for most Indian customers if Colour -> Cut -> Clarity.
In Southern India, where most customers are particular about dosham (defects), clarity is the most important consideration in selecting a diamond. Here, the order of priority is Clarity -> Colour -> Cut.
However, if a customer asks for a recommendation, Carat Lane always advices them to prioritize Cut and Colour over Clarity. This is because diamonds up to S1 grade are "eye clean". The inclusions are visible only under the loupe to a trained eye, and does not make any difference to the way the diamond looks
Is the shape the same as the cut?
No. They are different. The real "cut" as it is referred to deals with the quality of the final product in terms of its maximising the return of light.Four shapes of diamonds are the most popular: Round (or brilliant), Emerald, Marquis and Pear.
What is an "Ideal Cut"?
The "Ideal Cut" is a cut based on a specific set of proportions for a round brilliant diamond, proposed by gem cutter Marcel Tolkowsky in 1919. While Tolkowsky's original theories presented only one particular combination of proportions for creating the best balance of brilliance and dispersion, today the American Gemological Society recognizes any diamond falling within a narrow range of proportions and finish quality as being an "Ideal Cut" (also called an "AGS 0" or "AGS triple zero").
Essentially, the larger the table, the greater the brilliance at the expense of fire. A generally termed ideal cut will have a table percentage between 53% and 57% and a depth or height of 58% to 60%. Expect to pay 15%-20% more for an ideal cut stone. Avoid stones with table percentages above 70% or depths over 64% or under 57%.
I know that most rings have inclusions; what is OK and what is not?
Avoid the following flaws: 1.Large milky or cloudy areas 2. Big cracks...they threaten the durability. These include big feathers (big meaning 1/3 the diameter of the stone or more) 3.Big chips...they'll get bigger 4.Big white, black or coloured lines. They reduce brilliance and threaten durability
Is there any way to identify a poor cut?
Yes. Well, you can tell if a stone is poorly cut by looking for the following: 1. A white circle resembling a donut in the face-up view of a diamond. It occurs when the pavilion is too shallow and the girdle is reflected out. 2. Obvious dark spots/centres when viewed face-up. These indicate that the pavilion was cut too deep. 3.Extremely thick girdles reduce the brilliance and make the stone look small for its weight. 4. A girdle of uneven thickness (for reasons other than geometry) around the stone. One good way to see how well a stone is cut is to view it straight down on the table. The table and the four corners form a "square shape". On well-cut stones, the sides of the square will bow in "slightly". Sides that bow out are not ideal. A slight inward bowing may be tough to detect, so consider a seemingly perfect square to be a decent cut. Severely bowed in squares are also undesirable.
What is the shape of the diamond used in engagement rings?
The most common is the round brilliant cut. It reflects more light back from the table, accounting for the beauty of the diamond. Due to the facets or sides, inclusions (defects) are tougher to see. Some prefer the pear or marquis. The emerald cut is less common in sizes less than 1 carat. The value of the stone is affected in some cases by shape. Shapes other than round are called “Fancies.”
What is the best shape of diamond for an engagement ring?
The best shape of diamond for a ring depends on:
1. Personal preference
2. Desired brilliance (round brilliant cut has the most)
3. Weight (Fancies look more elegant in large sizes)
4. How big you want it to look (Fancies tend to look larger than white diamonds)
5. Shape and size of hand (experiment to find what is most flattering)
6. Colour and clarity of diamond (round brilliant cut hides defects and yellow tints best).
Why do they seem to follow this pattern?
Small round diamonds are more common, easier to cut, and easier to sell than fancies. About 75 per cent of the diamonds sold in the world are round brilliant cut diamonds! For larger stones, rounds are in higher demand and the supply is limited. The only exception is the large marquis, which is can cost as much as or more than the round brilliant.
How can I be sure that I receive the same diamond after sent for inspection or remounting?
Know where the inclusions are on your stone. Inclusions are the signature of diamond, which are the identifying marks. You can have it certified by the GIA for a fee. They will document the exact location of all identifying inclusions along with colour and carat. This is the exact and easiest way to identify your own diamond. You can re certify your diamond to compare it with the old certificate you have. Certification is not very expensive
What should I look for in the workmanship of the stone?
In a brilliant cut, 1.Make sure it is round. 2.Make sure the culet is not chipped or broken. 3.The girdle should not be too thick or too thin. 4.The girdle should be straight, not wavy from the sides. 5.The facets of the crown align with the facets of the pavilion; any misalignment will show itself in the girdle. 6.With a loupe or a scope, look closely at the girdle. Stones that are cut in a hurry will have small cracks that extend into the stone, making it look fuzzy or "bearded". Don't confuse this with the natural frosty colour of the girdle. 7.If the symmetry of the stone is off, or if it is damaged, extra facets may be added. 8.Be sure the table is parallel to the girdle and the culet (as seen through the table) is on-centre and undamaged.
Which are the most popular fancy colours in diamonds?
Fancy colored diamonds are called Z+ diamonds. These Z+ diamonds are the rarest hence the most expensive Z+ is more expensive than D s. Yellow and pink diamonds are the most commonly sought after fancy colours, and most likely will continue to be for years to come. Of late, there has been an increased demand for orange, blue, and green coloured diamonds. As they are rare in nature, supplies are limited, and demand can shift price
How are colour diamond prices determined?
Retail pricing is generally set by observing the prices of the competition, but prices depend on several factors: 1.Hue (the rarer the colour, the greater the cost) 2.Richness or saturation of the colour (ranging from very light to light to intense to vivid) 3.Purity of the colour (whether the colour is bright and clear, or clouded) Availability
What else should I know about colour diamond prices?
Remember that: 1.Clarity, colour distribution and cut together determine the cost of a yellow diamond. 2.Diamonds less than 0.80 carat can cost 10%-20% less. 3.Exceptionally well cut stones and stones with a VVS or IF clarity can cost 10%-20% more. 4.Secondary colours, such as brownish yellow, are less expensive.
Is a fancy coloured diamond judged for clarity just like a white diamond?
In a white diamond, clarity can make or break the stone, and VS clarity is usually ideal. For fancy colour diamonds, clarity is not the most important factor. A fancy colour diamond that is graded SI is still what is known as "eye clean," meaning that inclusions cannot be seen with the untrained, naked eye. Additionally, small pinpoints or feathers do not usually affect fancy colours due to the deeper colouring of the diamond. Fancy diamonds of VS or better clarity are more uncommon in nature and therefore command a greater price. Tip: If you cannot easily find inclusions under a 10 times magnification you should become suspicious; most likely it is not a real diamond. However, be aware of the fact that some gas bubbles in cubic zirconium may appear like inclusions if you do not look carefully.
Do colour undertones affect the diamond's worth?
A secondary undertone that enhances the color of a diamond is a plus. A secondary that detracts from the color is a negative. For instance: 1.A purplish pink color diamond can be worth more than a pink diamond, depending on the amount and intensity of purple 2.A brownish tint in a pink diamond usually decreases its value, and makes it a more affordable gemstone The predominant hue is always expressed as a noun, such as "pink." Any secondary colors will precede the primary hue and are usually expressed with an "ish" at the end, such as purplish pink. This means that the primary hue of the diamond is pink with some hints of purple throughout. If the grade is stated as two nouns—like "brown pink," it means the two colors are virtually even throughout the diamond.
What type of inclusions do you see most in colour diamonds?
In coloured diamonds, the inclusions are often crystals that exhibit much the same colour as the diamonds. To the untrained eye, these crystals blend right in with a diamond's colour and can create the appearance of more brilliance.
Are "champagne pink" diamonds desirable?
Champagne diamonds with a secondary pink colour are popular. When faced up, these stones display light to bold flashes of pink in their fire. Champagne diamonds are not as expensive as white diamonds. They are available in a sparkling range of champagne tones, from light to dark champagne and fancy cognac
What is the Bow-tie effect?
The bow tie effect, visible to the naked eye, is often observed in marquise, oval, pear and some heart-shaped diamonds. The bow tie looks like two triangular dark shapes joined at a point in the centre of the stone. It is caused by variations in the pavilion facet angles that are longer than wider. If prominent, it is considered a negative factor. In a well-cut diamond its appearance should be minimal or absent and certainly not a distraction.
What is a Cubic Zirconia?
Cubic Zirconia stones are a man-made diamond simulants with optical characteristics very close to natural diamonds. On the mohs scale of 1-10 for hardness, a CZ is 8.5 - 8.9, while a diamond is 10. Sand or dirt will not scratch a CZ or a diamond, but CZs and diamonds will both scratch glass. A CZ weighs more than a diamond, and this is a principal way to tell them apart.
What are "synthetic" diamonds?
Real diamonds have been created naturally through intense levels of heat and pressure deep within the ground. All natural diamonds are thought to be between 70 million and 3 billion years old. They are mined, cut and polished by highly skilled craftsmen, and are not otherwise tampered with. Synthetic or 'cultured' diamonds are created in the laboratory. All synthetic or 'cultured' diamonds must legally be declared as such. Carat Lane offers only are real and natural diamonds.
What are "conflict" diamonds?
There exists an illegal trade in diamonds in several parts of the world, and the money is used to fund conflicts (war and other outrages). These diamonds are called conflict diamonds or blood diamonds. Carat Lane is vehemently opposed to this trade in every form. We strive to assure that every diamond we sell is 'conflict-free’.
Does all Almaas by Nirakara Jewels diamond jewellery come accompanied with a certificate?
All diamonds used in our 'Create Your Diamond Ring' items are accompanied by their original and unique diamond certificate. Certification for items in our 'Diamond Jewellery Collection' depends on the size and quantity of the diamonds contained in the item.We do, of course, assure that all our diamonds are real, natural and "conflict-free".
Is it possible to have the certificate number 'engraved' onto the diamond?
Each GIA certified diamond of less than one carat in size has its unique certificate number microscopically laser inscribed into its girdle, meaning that there can never be any doubt that the diamond and certificate are one of the same. CaratLane also offers this service on other certified diamonds as well at the point of valuation. It is not possible to see this inscription with the naked eye, and extremely difficult to see even with a 10x magnifying loupe.
How does the HRD certificate compare to GIA certificate?
GIA is the oldest lab and so has become the most well-recognised and reputed, especially in the United States. On the other hand, HRD is well-regarded by the diamond community in Europe. HRD and GIA differ ever so slightly in systems of grading. Both strive to conform to their own system and overall, both do good and comparable jobs. You should to be able to buy a diamond with a high degree of confidence with either lab's report.
How do I choose the largest diamond within my budget?
Use the search option on Almaas by Nirakara Jewels that searches for loose diamonds and fill in your preferred budget details. You will get a range of stones that you can sort by size. Alternately, you can first enter the size of diamond you were considering (in case you do not want to buy anything less than a carat, for instance).You can choose your diamonds from CaratLane Colossal collection if the size does matter to you. Sort the search results to see which diamond in this size suits your budget.
I am looking for diamonds without black inclusions. How do I identify those?
Since diamonds are a natural substance, most come with some small internal flaws or inclusions that are like their defining characteristics, similar to birth marks. Completely flawless diamonds are extremely rare, and usually found only with collectors. For a good idea of the inclusions in a diamond, examine its certificate for a description of these. You need to have an idea of how the clarity of a diamond is measured, to understand the relative impact of black inclusions. For instance, diamond inclusions can be characterized as Slight, Very very slight etc. Visit the section on diamond clarity, for a better understanding of this.
Is it important that I buy a diamond that is accompanied by a certificate?
Yes. Buying with a certificate from a recognized authority such as the AGS, GIA, GSI or IGI means that your diamond has the credentials to be recognized worldwide as a valuable item. Resale values of diamonds drop drastically when unaccompanied by a certificate. Also, a certificate makes you sure about the authenticity and purity of your diamond.
Offers
Is there a limit to the discount value that one can avail?
The maximum discount that a person can avail is limited to Rs. 1,00,000 per order.
Payments
What is Cash on Delivery (CoD)?
Cash on Delivery (CoD) is a payment method where you pay for an item in cash, when the courier company delivers the item to you.
Is Cash on Delivery (CoD) available for customers outside India?
No, currently CoD is available only for customers residing in India.
How does CoD work?
You place an order for your favourite jewellery on CaratLane.com. Check for CoD facility by entering your area pin code in the text box. Choose CoD option if available and complete the order placement. You pay the complete amount in cash to the courier once the product is delivered to you. Please remember payment through cheque, draft or any other means will not be accepted by the courier.
Is CoD option available for all jewellery?
The CoD option is only available for Solitaires, Jewellery and Gold coins up to Rs.49,000.
Why is CoD option not available for my location?
Our CoD facility is limited by the reach of courier companies. Once you enter your pin code while ordering, you can check for the availability. If your location is not supported by the CoD service, please choose another payment option.
How long will it take for me to receive the product through CoD?
You will receive the product in 10 business days from the date of purchase.
Is there any additional charge for the CoD shipment?
No, our CoD service is done at no extra cost.
Can I offer cheque for the payment in place of cash?
No. CoD payments have to be made in cash only.
What is the option if no one is at home when the courier person comes?
Most courier companies will call you before coming over to deliver the item. Some important points to ensure that your CoD transaction goes smoothly Please ensure that the mobile number you provide for the Cash on Delivery payment is always available and answered. It is important that your address and landmark are very clear. This will help us locate you easily and complete the process faster. Please be available at the designated address with the complete cash as payment for the item purchased.
Shipping
Same Day Shipping
Products that feature under 'same day shipping' will be shipped the same day only if orders are placed before 1:00 pm.
For orders placed after 1:00 pm, shipping will happen the next day
Is same day shipping available for customers outside India?
No, currently same day shipping is available for customers residing in India. Multiple cross border regulations make it difficult for us to extend this feature to our international customers.
Can invoice not be a part of the shipment for delivery?
We do not ship any product without invoice because of intrastate and interstate requirement. (Document mandatory for goods transfer from one place to another)